Epoxy.com Product #25Epoxy Mortar KitDESCRIPTIONEpoxy.com Product #25 is a 100% solids epoxy resin and specially selected aggregate system. Units are preproportioned for ease of mixing and use on the jobsite. Epoxy.com Product #25 is a flowable, self-leveling grout, with handling and physical characteristics superior to similar grouts. ADVANTAGESEpoxy.com Product #25 Epoxy Mortar kit is a flowable, iron free, self-leveling grout, with handling and physical characteristics superior to similar grouts. ADVANTAGESEpoxy.com Product #25 is simple to use. Premeasured proportions allow for precise and repeatable results. Epoxy.com Product #25 is insensitive to moisture and may be used on dry and damp substrates. Pourable consistency - flows easily, self-levels in base plate forms, anchor bolt holes and floor toppings. Formulation permits placement up to three (3) inches thick. High strengths - 5,000 PSI compressive strength in twenty-four (24) hours at 73°F; ultimate strength averages 12,000 PSI in seven (7) days @ 73°. This makes it ideal for under equipment and where heavy loads, impact, torque and other operating stresses occur. Typical applications include:
PHYSICAL PROPERTIES
Compressive Strength ASTM C-109:
SURFACE PREPARATIONProper preparation of the substrate and contact area of the base plate is essential . Substrate must be both clean and sound. Remove laitance, oils and grease from concrete by sandblasting or bush hammering. If possible, sand blast bottom of base plates and wipe clean and dry. Apply grout as soon as possible after cleaning steel surfaces to prevent recurrence of oxidation. (If primer for steel base plate edges or top surface is required, use Epoxy.com PRODUCT #1200 Zinc Rich Primer. MIXINGInitial mix temperature must be 50°F minimum. For best performance, mix entire pack. Remove all components from six (6) gallon pail. Pour A Component into pail and add B Component and mix for two (2) minutes. Slowly add filler while continuing to mix resin until all is added or desired consistency. NOTE: Do not thin Epoxy.com Product #25. Solvent will prevent proper cure, and cause shrinkage. If less than full unit is required, carefully measure two (2) parts Component A and one (1) part Component B and add desired amount of filler. APPLICATIONConstruct containing form with head box, if necessary. Any form surface in contact with Epoxy.com Product #25 must be coated with release agent. Seal forms tightly to prevent leakage. Leakage that causes grout in place to subside below plate bottom level will cause loss of contact and voids at grout/base plate bottom interface. Re-establishing complete contact will be difficult at best. Be certain that all tools and mixing materials are at hand prior to mixing of Epoxy.com Product #25. Mix Epoxy.com Product #25 in accordance with mixing instructions. Pour grout into form from one side only. Pour continuously while maintaining a minimum of one (1) inch of head above the base plate bottom until grout appears full width of the base plate at opposite side of the form. Continue pouring at a reduced rate until Epoxy.com Product #25 levels at 1/4" above the plate bottom on all sides. Clean equipment with Epoxy.com Tool & Equipment Cleaner before Epoxy.com Product #25 hardens. If placement depth exceeds three (3) inches, contact EpoxySystems Technical Service for assistance. If ambient temperature exceeds 90° F, use Epoxy.com Product #27 Slow Cure Mortar PACKAGINGEpoxy.com Product #25 is conveniently packaged in a six (6) gallon pail. Each component is premeasured and separately packaged inside the six gallon pail. Yield is .50 cubic feet per unit. Component A - 128 fl. oz., Component B - 64 fl. oz., Aggregate - 3 ½ loose gallons. When pails are not available, premeasured 3½ loose aggregate will be packaged in paper polyethylene lined bags. CAUTION:CONTAINS EPOXY RESIN AND AMINE COMPOUNDS! May cause skin sensitization or other allergic responses. Avoid breathing vapors. Use with good ventilation. If contact with skin occurs, wash immediately with soap and water. If contact with eyes occurs, flush immediately with copious amounts of water for at least fifteen (15) minutes. Contact a physician. Wash contaminated clothing before reuse. Discard contaminated shoes. Wear protective clothing, goggles, gloves and/or barrier creams. FOR INDUSTRIAL USE ONLY KEEP AWAY FROM CHILDREN
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2011 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products] [Where to Start] [Bonding Systems] [Chip Floors] [Chemical Resistance] [Epoxy.com Coatings] [Conductive Electrostatic Dissipative] [Applications] [Elastomeric Polyurethane Systems] [Garage Floors] [High Temperature] [Industrial Floors] [Epoxy and Urethane Injection of Concrete] [Joint Systems & Sealants] [Mortars / Grouts] [Methyl Methacrylate (MMA)] [Novolac Epoxy] [Polymer Systems] [Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips][Product Guide] [Wood Filler] [Who We Are] [Guide Specs][FAQs] [Tech Data Sheets in Acrobat Format] [Epoxy.com MSDS in Acrobat Format] [Epoxy.com Online Ordering Authorization Form]
|
