Epoxy.com Product # 449
Elastomeric Membrane Waterproofing and
Reinforced Membrane Waterproofing
DESCRIPTION
Epoxy.com Product #449 Membrane Waterproofing and Reinforced Membrane Waterproofing
is a two-component, modified elastomeric material. After mixing and curing
it forms a tough, flexible waterproof membrane.
Epoxy.com Product #449 Membrane Waterproofing and Reinforced Membrane is applied to horizontal
surfaces of concrete, steel or wood to prevent penetration of moisture and
other deleterious substances. Typical applications are between slab waterproofing above and below grade.
Epoxy.com Product #449 Membrane Waterproofing and Reinforced Membrane may be applied in one coat up to 30
mil thickness on vertical surfaces without sag.
Epoxy.com Product #449 Membrane Waterproofing and Reinforced Membrane
replaces Epoxy.com Product #417, Epoxy.com Product #418, and Epoxy.com
Product #419 waterproofing membranes which are no longer made.
ADVANTAGES:
Epoxy.com Product #449 when used with inorganic fiber reinforcement, provides a puncture and tear
resistant shield to bridge construction joints and fine cracks.
PHYSICAL PROPERTIES:
Mixed Material:
| Color: |
Black |
| Solids by weight |
98 % min |
| Pot Life @ 75°F 2 (24°C) |
30 minutes |
| VOC Content |
0.3 lbs per gallon |
Cured Materials:
| Shore A Hardness |
ASTM D 2240-75 |
25 +/- 5 |
| Tensile Strength |
ASTM D 412 |
150 psi |
| Elongation |
ASTM D 412 |
500% |
| Tensile Strength @ 0°F |
|
200 psi |
| Water Vapor Permeability |
ASTM E 96 Method BW |
0.8 perms |
MIXING:
Combine equal amounts of Components A and B in clean container. Mix 2 -
3 minutes with low speed drill and an Epoxy.com Mixing Paddle. Apply immediately after mixing.
APPLICATION:
Prior to applying membrane, the surface to receive membrane must be dry, clean
and sound, all construction joints and cracks that are sizable must be bridged with fiberglass reinforcing cloth.
To produce a membrane, apply by brush, roller, spray or squeegee. For best results, two coats are recommended.
If reinforced cloth is used, it shall be embedded in the first coat of membrane while it still in a
liquid state. A grooved aluminum or plastic roller can be used for this purpose. After the first coat of membrane and
reinforcement has become tack-free, a second coat of membrane shall be applied.
COVERAGE:
On smooth concrete 80 sq. ft./G without Reinforcement
LIMITATIONS:
Epoxy.com Product #449 has an odor. If used indoors where such odor might be objectionable, it is recommended that
the material is tested before use to determine the appropriateness of its use. Material temperature at
time of mixing must be a minimum of 60°F (16°C), and surfaces to receive material must be a minimum of
40°F (4°C).
Once the container has been opened, the entire contents should be used as resealing may cause moisture,
contamination and skinning. When used in confined areas, good ventilation must be provided.
Damp surfaces could be detrimental to the performance of Epoxy.com Product #449.
PACKAGING:
Epoxy.com Product #449 is packaged in 2-gallon (7.57 liter) and 10- gallon (37.85 liter) units.
Epoxy.com Product #449 Primer for metal surfaces is available in 1-quart
(.946 liter), 1-gallon (3.785 liter), and 5-gallon containers (18.925 liters).
CAUTION:
Epoxy.com Product #449 contain coal tar and organic isocyanates.
These are considered irritants. Provide adequate ventilation. Avoid breathing vapors. Contact with skin
or eyes must be avoided. Wear protective clothing, gloves and/or protective cream and goggles.
Wash thoroughly with soap and water or a waterless skin cleaner prior to smoking
or eating. In case of contact with eyes, flush immediately with water and contact a physician immediately.
FOR INDUSTRIAL USE ONLY
KEEP AWAY FROM CHILDREN
|
|
Proper mixing and installation is critical to the optimal success
of all product. See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
350 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers. |
Copyright © 1994-2011 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;
Power Tools and Equipment 90 days; Vinyl Esters, and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
|