Epoxy.com Epoxy Concrete and
Wood Crack Injection Resin
Quick Epoxy Injection Comparision Chart
Epoxy.com Epoxy Crack Injection Resins
Epoxy.com has a wide selection of Epoxy Crack Injection Resins. Epoxy.com Epoxy Crack injection can be used for epoxy
injection of cracks in concrete. Epoxy.com Epoxy crack injection can also be used for wood. These same epoxy injection resins can
be used to inject plates to provide a flat bearing surface. The Epoxy.com Injection Resin System can be used for connection
plates between wood, concrete, and steel.
See www.epoxy.com/injection.aspx
for more details.
Epoxy.com Epoxy Crack Injection Resins - Cross Reference |
Epoxy.com
Product # |
Viscosity
CPS |
Compressive
Strength
psi |
Tensile
Strength
psi |
Pot Life
Minutes |
Minimum
Temperature
Degrees F |
ASTM Type |
Elongation
|
| 301 |
400-450 |
10,000 |
3,500 |
10 |
36° |
I,II,IV,V |
>10% |
| 302 |
500 |
14,000 |
8000 |
10 |
40° |
I, II, IV,V |
|
| 303 |
300 |
10,000 |
5,000 |
30 |
40° |
I, II |
|
| 304 |
500 |
14,000 |
|
10 |
33° |
I |
|
| 307 |
100 |
7,000 |
6,000 |
15 |
40° |
I, II |
2% |
| 308 |
500 |
15,000 |
8000 |
20 |
50° |
IV |
|
Epoxy.com Epoxy Crack Injection Resins
-
Epoxy.com Product #301 Injection Resin, low Modulus - a
100% solids low viscosity epoxy adhesive used to restore cracked
structural concrete by the pressure injection (epoxy crack injection) method and to grout cracks.
Meets ASTM C881 Types I, II, IV & V. Grade 1, Class
B &. C.
- Epoxy.com Product #301SC a longer Potlife version
of Product #301
- Epoxy.com Product #301Cold a faster version of Product
#301 typically used in Cold Temperature Cure applications, or where
a very fast set is needed
-
Epoxy.com Product #302 Injection a 100% solids low
viscosity moisture insensitive epoxy adhesive used to restore cracked
structural concrete by the pressure injection method and to grout cracks
in a horizontal plane by gravity. Meets ASTM C-881 Types I, II, IV & V. Grade 1, Class B &. C.
-
Epoxy.com Product #303 Low Viscosity Epoxy Injection Resin
a is a two component, 100% solids, moisture insensitive epoxy resin
system, mixed at a 2:1 ratio, with a viscosity of light-weight oil.
Product #303 exceeds the requirements of ASTM C 881-87, Types I, II,
Grade 1, Class "B" and "C". Use neat for grouting damp and dry cracks or
as a penetrating sealer on concrete, and wood. May also be mixed with
Special Fillers (Products #72-75), to create epoxy mortars.
-
Epoxy.com Product #304 Injection Resin and Mortar Binder
is a moisture insensitive, two-component, 100% solids epoxy resin system
designed specifically for use in temperatures of 40�F and below. It is
recommended for injection or anchor-bolt grouting in the neat state or
as a mortar when mixed with up to 3 1/4 parts of
Epoxy.com Product
#75 Filler (by volume).
Epoxy.com
Product #304 Injection Resin and Mortar Binder exceeds requirements
of ASTM C-881-90, Types I, Grade 1, Class A.
- Epoxy.com Product
#307 Low Viscosity Epoxy Injection Resin and Mortar Binder
is an Ultra-Low Viscosity Epoxy Resin System is a two component, 100%
solids, moisture insensitive epoxy resin system, mixed at a 2 to 1
ratio, with a very low viscosity for penetrating cracks. Epoxy.com
Product #307 Ultra-Low Viscosity Epoxy Resin Systems exceeds the
requirements of ASTM C 881 87, Types I, II, Grade 1, Class "B" and "C".
- Epoxy.com Product
#308 Ultra Low Viscosity Injection Resin for Load Bearing Applicationsis
an Ultra-Low Visocosity Epoxy Resin System for use as epoxy injection or
low viscosity epoxy mortar resin. It is 100% solids and is mixed 2:1 by
volume. Meets or exceeds the requirements for ASTM C881 Types I and IV,
Grade 1, Classes B &C.
Epoxy.com Port Setting (Epoxy Gel) Adhesives
- Epoxy.com Product #5 Fast Set Gel Adhesive is a 100%
solids high-mod epoxy gel adhesive used for vertical and overhead bonding
applications and structural repairs. It is also used as a grout for anchor
bolts, dowels and rebar. Meets ASTM
C-881-90 Type I, II, IV, & V when used at temperatures of 40° F. and
below.
- Epoxy.com Product#6 Gel - Normal Setting Adhesive is a high-mod epoxy gel adhesive used for vertical and overhead bonding applications and structural repairs. It is also used as a grout for anchor bolts, dowels and rebar.
Exceeds requirements for A.S.T.M. C-881-90 Types I, II, IV Grade 3, Class "B"
and "C".
- Epoxy.com Product #6SC Long Pot life Adhesive produces a non-sagging material that is ideal for repairs on vertical or overhead surfaces. PRODUCT #6SC meets or exceeds the requirements of
ASTM - C881-87, Types I, II, and IV, Grade 3 Class "B" and "C".
ASTM C 881 Epoxy Types
Type I: For use in non-load
bearing applications for bonding hardened concrete to hardened concrete and
other materials, and as a binder in epoxy mortars or epoxy concretes.
Type II: For use in non-load
bearing applications for bonding freshly mixed concrete to hardened
concrete.
Type III: For use in bonding
skid-resistant materials to hardened concrete, and as a binder in epoxy
mortars or epoxy concretes, used on traffic bearing surfaces (or surfaces
subject to thermal or mechanical movements).
Type IV: For use in load bearing
applications for bonding hardened concrete to hardened concrete and other
materials and as a binder for epoxy mortars and concretes.
Type V: For use in load bearing
applications for bonding freshly mixed concrete to hardened concrete.
Type VI: For bonding and sealing
segmental precast elements with internal tendons and for span-by-span
erection when temporary post tensioning is applied.
Type VII: For use as a non-stress
carrying sealer for segmental precast elements when temporary post
tensioning is not applied in span-by-span erection.
Epoxy Grades
Grade 1: Low viscosity
Grade 2: Medium viscosity
Grade 3: Non-sagging consistency
Epoxy Classes
Classes A, B, and C are defined for types I-IV. Classes
D, E, and F are defined for Types VI and VII according to the range of
temperatures for which they are suitable.
Class A: Below 40°F to manufacturer defined low
Class B: 40° - 60°F
Class C: Above 60° F to manufacturer defined high
Class D: 40°-65°F
Class E: 60°-80°F
Class F: 75°-90°F
|
|
Proper mixing and installation is critical to the optimal success
of all product. See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
350 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers. |
Copyright © 1994-2011 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;
Power Tools and Equipment 90 days; Vinyl Esters, and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
|